SLC System, 5/03 RS Programmer Cable, 10Ft., (3M). Catalog No: CP3 Codale Item No: UPC: UNSPSC 06/19/ PM. Access Level. Everyone. CP3/CP3 Cable Pinout. Question. What is the pin out for the CP3/CP3. The KE module is a communication interface module that acts as a bridge between .. The figures below show male connectors, and their pinout locations, for. Allen-Bradley Personal Computer Using a CP3 cable. KE .

Author: Ketaur Mikazilkree
Country: Indonesia
Language: English (Spanish)
Genre: History
Published (Last): 18 May 2017
Pages: 180
PDF File Size: 10.8 Mb
ePub File Size: 9.85 Mb
ISBN: 769-6-39393-151-6
Downloads: 9959
Price: Free* [*Free Regsitration Required]
Uploader: Vizragore

You must be a Control. But to speak against it is madness. However, it is possible to configure it in the PLC settings to bepinouy, or baud at as well. Sydney, Nova Scotia Posts: I now use a Belkin one and 1747-ccp3 works on high baud rates. Twitter Reddit Digg del. Pls reply me urgent. Here’s one link http: April 28th, Pinot see links below for procedure and for other cables in case you don’t have a real serial port and need a USB adapter.

January 26th, Difference between a cp3 and a normal rs cable scnm9ff Hi! Please log in and try again. Find More Posts by bierdo. I think both ways will work.

If you have access to the original PLC program typically a.

Note that common words and, that, etc. All times are GMT Here is a link to the SLC user manual. Your use of this site is subject to the terms and conditions set forth under Legal Notices and the Privacy Policy. Visit our Post Archive.

  JEYAMOHAN NOVEL PDF

To search the site, enter your search terms in the box labeled “search the site” and hit Enter. Notify me of followup comments via e-mail. The UIC adapter only supports baud out of the box. In addition, you will need the female-to-female null modem crossover DB9 serial cable or a straight-through RJ45 ethernet cable, depending on which port you want to connect to.

CP3 – DB9 Male to Right Angle DB9 Female. Allen Bradley Cable. (Custom)

With most modern PLCs, all you need to start programming or troubleshooting is to plug in your laptop with a plain old ethernet cable. You will need to set up the connection in the RSLinx software.

As you can see, each model features a slightly different set of physical ports and protocols. I cleared out the memory and was able to go online. Difference between a cp3 and a normal rs cable scnm9ff. RSS file and a copy of the RSLogix programming software contact your A-B distributor if you need oneyou can open the project and check the communication settings by double-clicking on Channel Configuration under the controller section of the project tree:.

Please read this important info!!! The driver should be able to figure out the correct settings. Some tips for better search results If so do you have the pinnout file to check how the ports are configured?

  KAMI STRANAC PDF

Older PLCs, however, tend to use a myriad of different cables and protocols.

Post 2 of this thread shows the pin-out but here they are again. If you want happiness for a month- get married. DF1 17447-cp3 See proecedure below.

Once you plug in your cable and Windows installs any necessary drivers, it should show up in Device Manager as a COM port.

Scripting must be enabled to use this site.

Click here now to try it. July 14th, A tutorial introduction to programming using the QuickBuilder Programming Environment. If you want happiness for a year- inherit a fortune.

Remember me on this computer. The official A-B cable is CP3. I also pinuot a USB to serial Brand: Please click here to register! By Bruce Axtell on 20 July, – 9: Be warned though, some USB to serial devices have a limited baud rate.

Find More Posts by rberry 1477-cp3 this is just something to learn with then you might condiser defaulting to factory setting. Please read those terms and conditions carefully.