Interfacing With Microprocessor A interface to microprocessor. Module 3: I/O programming: I/O addresses MAP of x86 PC’s, programming and . To have more pins for I/O, the is interfaced to – a PPI (Parallel. Microprocessor | (programmable peripheral interface) · Interface with Subtract content of two ports by interfacing with microprocessor first_page program to determine subtraction of corresponding elements of.

Author: Gazshura Nira
Country: Maldives
Language: English (Spanish)
Genre: Literature
Published (Last): 17 March 2008
Pages: 415
PDF File Size: 14.5 Mb
ePub File Size: 8.56 Mb
ISBN: 447-6-28555-323-3
Downloads: 77979
Price: Free* [*Free Regsitration Required]
Uploader: Tauk

Interfacing with We think you have liked this presentation. If you wish to download it, please recommend it to your friends in any social system.

– I/O Interfacing – I/O mapped I/O – ppt download

Port A acts as a 8-bit input data port to receive the digital data output from the ADC. Out of these 8 inputs only one can be selected for conversion by using 3 address lines A,B,C.

Design of Microprocessor-Based Systems Dr. Your email address will not be published.

8255A – Programmable Peripheral Interface

Leave a Reply Cancel reply Your email address will not be published. The CPU may drive these lines using output port lines in case of multichannel applications.

To use this website, you must agree to our Privacy Policyincluding cookie policy. Thus the name Hardware Triggered Strobe. Intel CPU Structure. An operational amplifier is used as a current — to — voltage converter at the output of AD In1 clock period of 1 Hz frequency clock-No. Input Output Interfacing Techniques. OUT is initially High.

  CATALOGO MATERIALE ELETTRICO BTICINO PDF

Preset count is loaded – OUT is high. To make this website work, we log user data and share it with processors. Pin Diagram of Debugging a Program in Ports are configured as input ports Input on reset CS – Used to select the chip. To get absolute address, all remaining address lines A 3 — A 19 are used to decode the address for GATE can be connected to line and made 1 by software.

Mode 5 – Hardware Triggered strobe. Published by Derick Warren Modified over 3 years ago. Explain the mode of operation and initialisation. The sequence of pulses can be decided, depending upon the required motion of the shaft.

Interfacing with Microprocessor | Interfacing with

Thus a clock pulse of desired frequently can be produced. Once solution is similar to – This can be solved in many ways.

Modular Programming in Microprocessor. Mode Interrupt on terminal count.

Feedback Privacy Policy Feedback. It employs rotation of its shaft in terms of steps, rather than continuous rotation as in case of AC or DC motors.

No continuous pulses are generated. Types of Interrupts. Explain the mode of operation and initialization.

Supporting Circuits of Microprocessor. When Read back command for status is sent to control register. To rotate the shaft of the stepper motor, a sequence of pulses is intwrfacing to be applied to the windings of the stepper intrefacing, in a proper sequence.

  HSMS 2805 PDF

To make this website work, we log user data and share it with processors. To get absolute address, all remaining address lines A 15 — A 2 are used to decode the address for Maximum Mode Configuration of The DAC find applications in areas like Digitally controlled gains Motor speed controls Programmable gain amplifiers etc.

My presentations Profile Feedback Log out. Binary level pulses of v are required at its winding inputs to obtain the rotation of shafts. By using indirect address method this range can be extended upto 2 16 addresses. About project SlidePlayer Terms of Service.

Feedback Privacy Policy Feedback. Port C is selected as a whole i. Preset value is reloaded and operation restarts. The Pulse width depends on the count value. The angle x may be calculated as: Thus pulses are produced continuously in mode 2 Mode 4 – When count reaches terminal count i.

Auth with social network: The format of status register is shown. Published by Arleen Gray Modified over 2 years ago. In one clock period of 10 KHz frequency there are clock periods of 10 MHz frequency.