Falling Weight Impact Tester. Designed and built with operator simplicity in mind, the Ray-Ran Universal Falling Weight Impact Tester is simply the best in its. ASTM D covers the process used to determine the resistance of thermoplastic pipe and fittings to impact by a tup (falling weight) under defined conditions. Find out all of the information about the Chengde Jinjian Testing Instrument product: impact tester / for pipes ISO, ASTM D | JJWI, JJWI

Author: Dougis Faek
Country: Angola
Language: English (Spanish)
Genre: Sex
Published (Last): 21 December 2018
Pages: 398
PDF File Size: 19.23 Mb
ePub File Size: 16.66 Mb
ISBN: 590-1-98221-251-9
Downloads: 88110
Price: Free* [*Free Regsitration Required]
Uploader: Fenrikazahn

Results gathered by this test can be used as the basis for establishing impact test requirements in product standards; to measure the effect of changes in materials or processing on the product and to measure any effects of the environment on the pipe or fittings.

ASTM D Pipe falling weight impact test – ASTM – United Test

The mass of the tup shall be 6, 12, 20 or 30 lbs 2. Historical Version s – view previous versions of standard. R2444 the basis for establishing impact test requirements in product standards. Two specimen holders are described. This test method covers the determination of the impact resistance of thermoplastic pipe and fittings under specified conditions of impact by means of a tup falling weight.

To fully protect the operator from flying debris we include and offer a selection of interlocked safety enclosures. The impact resistance of thermoplastic pipe and fittings relates to suitability for service and to quality of processing.

  HR23-700 MANUAL PDF

It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Subscribe to Instron News!

Three interchangeable striking noses are used on the tup, differing in geometrical configuration. There are three interchangeable inserts for the tup, Type A is a cone with a rounded point, Type B is a cylinder with a relatively flat surface, and Type C has a 0.

ASTM D2444 Impact Resistance of Plastic Pipe and Fittings

To measure the effect of the environment. Glossary of Materials Testing Terms. ASTM D, tup nose detail. The mass of the tup shall be 6, axtm, 20 or 30 lbs 2. The large area below offers room for larger diameter pipes up to 12 inches.

By continuing to use our site, you accept our cookie policy. Link to Active This link will always route to the current Active version of the standard. See Appendix X5 for guidelines for selecting testing combinations.

Asm D – 99 Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup Falling Weight This test method covers the determination of the impact resistance of thermoplastic pipe and fittings under specified conditions of impact by means of a tup falling weight. WaveMatrix 2 for Dynamic Testing. Description Literature Contact Us ASTM D covers the process used to determine the resistance of thermoplastic pipe and fittings to impact by a tup falling weight under defined conditions.

  CATALOGO RODAMIENTOS RHP PDF

Email addresses can only contain letters, numbers and the following special characters: See Appendix X4 for guidelines for selecting testing combinations. For pipes over that we offer larger, extended support tables. Subscribe to Our Newsletters. Software for Series Systems.

ASTM D – 99 We use cookies to improve your browsing experience. Impact resistance may also provide a relative measure of a material’s resistance to breakage during handling and installation and, for non-buried applications, to in-service breakage.

Impact resistance is one of the most important properties for component designers to consider, as well as the most difficult to quantify. Two specimen supports either a V-block or e2444 Flat Plate are defined in the standard. Two specimen holders are described. One piece of information that may not be found without the use of instrumentation is the first crack or incipient damage point. Two specimen supports either a V-block or a Flat Plate are defined in the standard.