Advanced Melt Flow System. The 6MPCA is the most advanced digital model offered within the Ray-Ran range of melt flow index testers. The operating. Find the most up-to-date version of ASTM D at Engineering ASTM D(). Standard Test Method for Flow Rates for Poly(Vinyl Chloride) with Molecular Structural Implications. standard by ASTM.

Author: Mauzshura Kajirn
Country: Nicaragua
Language: English (Spanish)
Genre: Life
Published (Last): 11 April 2005
Pages: 359
PDF File Size: 19.89 Mb
ePub File Size: 8.11 Mb
ISBN: 573-3-12263-116-3
Downloads: 97922
Price: Free* [*Free Regsitration Required]
Uploader: Kami

WaveMatrix 2 for Dynamic Testing. Thus, implications with respect to PVC molecular structural changes can be detected and predicted. The instrument is now ready for the next test. Concrete, Asphalt and Rock. This average value is the PVC?

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. This test method is used for quality-control tests on PVC compounds that have asm wide range of melt viscosities. However, as a one-point measure of flow relative to shear rate, its one drawback is that the same PVC melt flow values can be obtained for materials having different processibility; the chance of this happening is minimized, however, if the compounds are similar in sstm.

ASTM D3364 Flow Rates for Poly Vinyl Chloride

Put the die hot into methyl ethyl ketone in order to break the PVC skin away from the ori? For PVC, N varies from 0. Be careful not to squeeze the specimen; the specimen satm

  CALCULO DE LIQUIDOS EN PEDIATRIA PDF

By continuing to use our site, you accept our cookie policy. Link to Active This link will always route to the current Active version of the standard.

Divide the difference by the average and multiply by The principles of It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Report as percent PVC instability.

Thus, this test is able to detect and follow profound changes which occur during extrusion, injection molding, milling, or mixing. The dimensions of the regular die are shown in Fig.

Description Contact Us This test method is used d3346 quality-control tests on PVC compounds that have a wide range of melt viscosities. Last previous edition D — Email addresses must contain the symbol. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? The sensitivity of the material to temperature necessitates slightly tighter controls than those stated in Test Method D Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

However, as aztm one-point measure of?

Correlations with a wide range of processing conditions have supported the conclusions that little or no change in adtm occurs during the test. Fluctuations up and down repeatedly during a run can indicate nonuniform mixing or a bad charging technique. The sensitivity of the material to temperature necessitates slightly tighter controls than those stated in Test Method D Measurements are made at shear rates close to 1 s?

  AVANTALK BTCK-10B MANUAL PDF

ASTMD Standard Test Method for Poly(Vinyl ride) with Molecular Structural Implications_百度文库

Precision and Bias Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. When charging is complete, pack down the PVC with the phenolic-coated charging tool by repeated thrusts.

Make the cut quickly and neatly for best precision. If instability still occurs, particularly at high? The sensitivity of this test method makes it useful for correlating with processing conditions and as an aid in predicting changes in processing.

NOTE 4—A positive instability probably indicates that crosslinking is occurring. The data in Table 3 should not be rigorously applied to acceptance or rejection of material, as those data are speci? Note 1—There is no known ISO equivalent to this standard. Summary of Test Method 4.

This means that the?