ASTM D – Designation: D /D M – 06 Standard Test Methods for Shear Adhesion of. ASTM D/DM: Standard Test Methods for Shear Adhesion of Pressure- Sensitive Tapes. A summary of ASTM standards relating to pressure sensitive tape is attached. The shear test procedures are also harmonized: ASTM D and PSTC.

Author: Taujora Kenos
Country: France
Language: English (Spanish)
Genre: Literature
Published (Last): 20 July 2010
Pages: 359
PDF File Size: 8.32 Mb
ePub File Size: 20.18 Mb
ISBN: 981-2-43776-950-9
Downloads: 71712
Price: Free* [*Free Regsitration Required]
Uploader: Arashigore

Your comments will receive careful consideration at a meeting of the responsible technical committee,1 which you may attend. Allow the remaining mm [8 in.

This standard is not included in any packages. No single value shall be considered as representative of the roll under test. Width of specimen for Procedures E, F, and G if other than 12 mm [0. The surfaces of similar fiberboards may exhibit considerable variation between mills, between batches from one mill, and within batches.

The radius of the curvature of the? The values stated in each system are not be exact equivalents; therefore, each system shall be used independently of the other. The roller shall move either mechanically or by hand at the rate of 10 6 0. The use of an elevated temperature during test tends to reduce the duration of the test. The use of an elevated temperature during test tends to reduce the duration of the test.

You may delete a document from your Alert Profile at any time.

ASTM D Standard: Shear Adhesion Tester for Pressure Sensitive Tapes

This standard is subject to zstm at any time by the responsible technical committee and must be reviewed every? Good cohesion is necessary for clean removal. Combining values qstm the two systems will result in non-conformance with the standard. Identification number of the company: The adequate solution for the transport of your fresh products or frozen food or of your organic and This may be used to compare the shear adhesion of a tape to a particular? Only the sellers and buyers responsability is involved in case of dispute.

  LOURDES MUNGUIA EN PLAYBOY PDF

This may be used to compare the shear adhesion of a tape to a particular fiberboard surface or to compare the shear adhesion of a tape to a variety of fiberboard surfaces. For Procedures A and H, asgm steel panel instead of?

Owen Zhang86 A standard mass is attached to the free end of the tape and allowed to act for a speci? Do not touch aztm panel surfaces with? Adhesion is a bond produced between a pressure-sensitive tape adhesive and a surface for Procedures A, B, C, D, and H; and, Wholesalers ads Partners Websites.

It may be desirable to mask the exposed adhesive of the free end of the specimen. NOTE 3—Take care that the?

Already Subscribed to this document. Precision and Bias This standard has been approved for atm by agencies of the Department of Defense. Your Alert Profile lists the documents that will be monitored.

One company reports that, with care, the between laboratory standard deviation and the residual including within roll standard deviation may be higher or lower than reported here, depending on the tape type and manufacturer. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards.

ASTM D shearing tester Cell Instruments Co Import Export

Between uses, the panels test surface shall be protected from scratches and contamination, and the panels stored at conditions described in 8. The assessment may be within a roll of tape, between rolls or production lots.

  FREEDOM EVOLVES DANIEL DENNETT PDF

Standards Subsctiption may be the perfect solution. ASTM D The test plate with adhesive specimen is vertically hanged on the stand and its bottom is attached with a standard weight.

If it is desirable to test slightly different widths for example, 25 of 50 mm of specimens per 8. Algomtl allows the purchase and sale of lots from manufacturers, wholesalers and retailers.

ASTM D3654/D3654M – 06(2011)

Procedure D measures the shear adhesion of a pressure-sensitive tape to a nonstandard fiberboard, liner board, corrugated board, or other surfaces which is agreed upon for testing. Link to Active This link will always route to the current Active version of the standard.

Obtain the arithmetic mean of all logarithms and then convert back to time by obtaining the appropriate antilogarithm. Take care in the choice of samples and when comparing results between fiberboard surfaces which d354 not be exactly the same.

You can also visit our FAQ section and see our information section on the risks associated with counterfeiting.

This gives the test results for the roll of tape under consideration in the sampling plan. Axtm results are available. These censored data may have a time asmt termination rather than a time to failure. Between laboratories Between testers Between rolls Residual 0. The values stated in each system are not be exact equivalents; therefore, each system shall be used independently of the other. A number in parentheses indicates the year of last reapproval. The mass of the clamp or hook described in 5.