ASTM Ea, Standard Practice for Use of the International System of Units. ISO , SI Units and Recommendations for the Use of Their Multiples. ASTM E [ Withdrawn ]. Standard for Metric Practice. standard by ASTM International, 01/01/ View all product details. Most Recent. Find the most up-to-date version of ASTM E at Engineering

Author: Vole JoJoll
Country: Bulgaria
Language: English (Spanish)
Genre: Software
Published (Last): 25 August 2011
Pages: 302
PDF File Size: 16.94 Mb
ePub File Size: 5.60 Mb
ISBN: 873-1-71706-390-3
Downloads: 27751
Price: Free* [*Free Regsitration Required]
Uploader: Tojataxe

ASTM E – 79 Standard for Metric Practice

Also known as hot strength. This standard does not purport to address all of the safety problems associated with its use. The fourteen remaining items of controversy were resolved and the new document could have been issued in However, you may download material from The Drafting ZONE on the Web one machine readable copy and one print copy per page for your personal, noncommercial use only.

The stand shall be adjustable to setting the test panel at any desired slope, at any horizontal distance from the lower edge of the duct opening, and at various angles incident to the wind direction.

Do not apply pressure to the shingle tabs either during or after application. Search Drafting Zone Resources. All materials contained on this site are protected by United States copyright law and may not be reproduced, distributed, transmitted, displayed, published or broadcast without the prior written permission of Genium Group, Inc. Plastics suitable for plating are acrylonitrile, butadiene, styrene, polypropylene, and polysulfone.

This method, assisted by experience and engineering judgment, will also prove useful for development work. The service condition designation is for protection against wett. Enter one or more keywords separated by spaces. Test another panel at the position judged to be most critical on the basis of the first three tests.


This method is suitable for use in specifications and regulatory statutes. Full details are available upon request from Genium Publishing Corporation.

These materials are manufactured by various companies and may be known as various trademark products. Secure the shingles at the outer edge of the test panel by exposed nailing to simulate anchoring at the rake edges of a roof deck.

Avoid the use of trade names for the specification of materials. The wood test deck shall be of such rigidity that it will not twist or distort with normal handling, or vibrate from the wind velocity during the test.

There was a problem providing the content you requested

No cement, other asttm the factory-applied adhesive, shall be used to fasten down the tabs. The end point for failure shall be taken as the time at which the sealing feature fails to restrain one or more full shingle tabs, or a locking ear or tab of a lock shingle tears loose or disengages from its locking position or a non-rigid component is damaged so as to affect the performance of the system. You may not alter or remove any trademark, copyright or other notice from copies of the content.

Hot-dipped – Has an.

2017 Florida Building Code -Test Protocols for High Velocity Hurricane Zone, Sixth Edition

An example of this would be SAESteel. Inspection of parts should be in accordance with Astmm standards. When specifying special materials, furnish a more complete description to facilitate procurement and incoming inspection.


No undercoating is required on steel substrates.

This effort is entering its third year. If the project engineer should require other service conditions, they should be specified in accordance with ASTM standards, as noted above. It is the responsibility of the user to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Local wind conditions may differ from the test conditions both in intensity and duration, and should be taken into consideration. Dual dimensioning practices are also to be discouraged for commercial applications in new design.

The test incline shall be 2: The target course shall be the third course up from the bottom of the test specimen. The cell or room shall be capable of receiving a minimum 50 in.

In addition, no free portion of a shingle or non-rigid component shall lift so as to stand asttm or bend back on itself during the test. However, if the use of a trade name is necessary, include the name of the ve. If a particular type or grade of material lends itself to the fabrication desired, it should be specified. Definitions from the Florida Building Code, Building shall take precedence.

It also facilitates soldering and antigalling.