BC Datasheet, BC PDF, BC Data sheet, BC manual, BC pdf, BC, datenblatt, Electronics BC, alldatasheet, free, datasheet, Datasheets, . ABSOLUTE MAXIMUM RATINGS. PARAMETER. SYMBOL. VALUE. UNIT. Collector-Base Voltage. VCBO. V. Collector-Emitter Voltage. VCEO. V. 2SC Transistor Datasheet pdf, 2SC Equivalent. Parameters and Characteristics.

Author: Durisar Zulkibar
Country: Pakistan
Language: English (Spanish)
Genre: Technology
Published (Last): 1 September 2015
Pages: 423
PDF File Size: 13.29 Mb
ePub File Size: 7.52 Mb
ISBN: 831-7-60649-229-3
Downloads: 31317
Price: Free* [*Free Regsitration Required]
Uploader: Bataur

Complete Technical Details can be found at the BC transistor datasheet give at the end of this page. The current gain may vary between and For switching applications, transistor is biased so that it remains fully on if there is a signal at its base.

It is used for amplification and switching purposes. The variants of BC are A, B and C which vary in datassheet of current gain and other characteristics.

TL — Programmable Reference Voltage.

BC is general purpose silicon, NPN, bipolar junction transistor. The maximum DC current gain is Arduino based GPS receiver. The maximum amount of current that could flow through the Bf458 pin is mA, hence we cannot connect loads that consume more than mA using this transistor. When used as an Amplifier the DC current gain of the Transistor can be calculated by using the below formulae.


The transistor terminals require a fixed DC voltage to operate in the desired region of its characteristic curves. To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA. As mentioned the biasing current should be maximum of 5mA.

BC is used in common emitter configuration for amplifiers. Skip to main content. Interface SD Card with Arduino. When this transistor is fully ratasheet, it can allow a maximum of mA to flow across the collector and emitter.

Anything more than 5mA will kill the Transistor; hence a resistor is always added in series with base pin to limit the current. The value of this resistor R B can be calculated using below formula.

Transistor BC548

Choosing Battery for Robots. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV.

Its equivalent transistors are 2N and 2SC The voltage divider is the commonly used biasing mode. BC has a datashest value of tothis value determines the amplification capacity of the transistor.

BC Datasheet pdf – Si-Epitaxial PlanarTransistors – Diotec Elektronische

SPI Dwtasheet of Arduino. A Transistors acts as an Amplifier when operating in Active Region. Amplifier modules like Audio amplifiers, signal Amplifier etc. The value of I B should not exceed 5mA. When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above.


Choosing Motor For Robots. As discussed a transistor will act as an Open switch during Forward Bias and as a closed switch during Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base pin. For amplification applications, the transistor is biased such that it is partly on for all input conditions.

In the absence of base signal, it gets completely off. It can amplify power, voltage and current at different configurations. Of the above types common emitter type datashest the popular and mostly used configuration.

What is Web Browser. Interface GPS with Arduino. The input signal at base is amplified and taken at the emitter.

2SC458 Datasheet, Equivalent, Cross Reference Search

BC is a NPN transistor so the collector and emitter will be left open Reverse biased when the base pin is held at ground and will be closed Forward biased when a signal is provided to base pin. These equivalent transistors however have different lead assignments.

Virgin Galactic — Commercial Space Flight.