But apparently down this path Bob Boyce took towards TPU-like scalar energy, of precise frequency control and heterodyning, lies the ability to. (As of Nov. ), A South African experimenter has modified an electrolysis circuit developed by Bob Boyce so that now it recharges his daughter’s electric. The Bob Boyce Plate Cell & PWMG3 & Toroid Coil & Plans. Given Away to the Public, to Further Mankind. Written by Patrick Kelly. Bob Boyce is easily the.
|Published (Last):||12 July 2013|
|PDF File Size:||5.68 Mb|
|ePub File Size:||10.47 Mb|
|Price:||Free* [*Free Regsitration Required]|
Doesn’t look like much When I told him that the primaries control coils could even be fed open-ended with potential, he seemed to think I was nuts!
I only provided them with the toroid winding and connection information, power requirements, preliminary tuning instructions, and some safety advice. Each primary MUST have the same exact number youchoose.
Bob Boyce TPU
My end goal is a stable TPU with air core and n excitation coils, biyce n could easily be 8, 16, or even The riskier and higher performance toroidal power system uses both the DC potential bias and a magneticbias. But stranded ml-spec silver plated Teflon insulated wire is still better than magnet wire.
Free Energy searching for free energy and discussing free energy. The output is a combination of both, but the load determines exactly how much can be harvested from thelongitudinal side.
That was one of the driving forces that led me to develop the Hex Controller. As you may or may not know, some loads work fine off of longitudinal flow cold tphbut many donot. The toroid core bottom face longitudinal winding is done. So sure, it is a trade-off of control vs.
When the dominant energy is kicked, it can kick back – hard! Try to make sure that the wires are tight against one another on the inside circumference of the core, and evenly spaced on the outside with none bunching up closer than others. I used this circuit to test pulsing a single coil from both ends with frequencies. Oh, the frequency was 7KHz and the pulse with was ns.
Otherwise, both seem to build up a swirling electromagnetic vortex during operation. Anyways, in Bob’s main publicly available controllers designs for this, he does not include the ability to self-tune the frequencies so they are exact multiplesnor does he boyyce the ability for phase control frequencies at specific phase offsets. DC to DC converter. New monetisation for all members.
Free Energy: Bob Boyce Resonant Toroid
By the way, tpj can chat with you now if you get on Skype. As you probably already know, several years ago, I went back into the hydroxy gas research that I had stopped doing in the early 90s. Using a vitamin C powder bottle, we lock the center in place, and melt inwax to solidly secure the windings in the toroid hole. These are driven in aWye configuration.
Bob Boyce TPU thread
They can stick their collective heads in the sand all they want, as that does not change how this universe operates. Rigol DSZ is one of the best 4 channel digital scopes on the market today.
Did you miss your activation email? Tou least they don’t require maintaining andtracking the resonance reaction of the water to keep the system in tune for maximum hydroxy gas production. In pulsed mode, it is the water load doing theconversion, not the toroid itself.
Here’s a link to the page to order samples if you are interested: This setup is so far out of spec that I am not expecting any overunity, I just thought that the effects would at least try to manifest themselves in some small way Eldarion Yes, like Bruce just said, leave the ground of the secondary separate goyce the others but connected to load.
I wish there was a way to release this circuit without the dangers that goes with it. For tpuu other applications, a capacitor would probably be required to isolate the load from the DC bias potential, while passing the energy to drive the load. This means maintaining control over the phase interrelation of all signals involved.
It is a concept that Steven Mark had confirmed as correct