Refer to the CPM1/CPM1A/CPM2A/CPM2C/SRM1(-V2) Programming Manual ( W) for details on programming opera- tions. CPM2C Features and. Part number. Operation manual. CPM2A operation manual. W Programming manual. CPM1/CPM1A/CPM2A/CPM2C/SRM1(-V2) Programming Manual. All OMRON products are capitalized in this manual. The word “Unit” is also capitalized when it refers to an OMRON product, regardless of whether or not it.

Author: Vitaxe Fenriktilar
Country: Lithuania
Language: English (Spanish)
Genre: Environment
Published (Last): 11 September 2012
Pages: 72
PDF File Size: 1.35 Mb
ePub File Size: 12.18 Mb
ISBN: 340-5-58936-930-1
Downloads: 37794
Price: Free* [*Free Regsitration Required]
Uploader: Mikagul

Inputting a New SV This operation can be used to input a new SV constant, as well as to change an Constant SV from a constant to a word address designation and vice versa. Handling 1, 2, Chapters Table Of Contents Page 48 Refer to the Programming Manual for details.

Reading status Check AR comparison in Follow the handling precautions and pro- cedures to properly use the Unit. Also, the CPM2A CPU Unit is a stand-alone Unit that can han- dle a broad range of machine control applications, so it is ideal for use as a built- in control unit in equipment.

External safety measures must be provided to ensure safety in the system.

Press the CLR Key cmp2a bring up the initial display. Example Program Section Example Program The following ladder program will be used to demonstrate how to write a pro- gram with the Programming Console.

Unit Components Section Input the normally open condition IR When a minimum cycle time has been set, CPU operation is paused after pro- gram execution until the minimum cycle time is reached. Is PWR indicator lit? These differences are caused by changing execution conditions. Page 29 One analog output: Are the terminal screws loose? Clear the memory before entering a new program.

  EN LA ARDIENTE OSCURIDAD ENGLISH TRANSLATION PDF

Wiring and Connections Section Floor Ducts Leave at least mm between the wiring and the maual of the duct, as shown in the following diagram. Page Authorized Distributor: Output Short Protection The output or internal circuitry might be damaged when the load connected to an output is short-circuited, so it is recommended to install a protective fuse in each Check the voltage at the Wire correctly.

OMRON CPM2A – MANUAL Pdf Download.

Specifications subject to change without notice. It is assumed here that the causes of any of the errors for which error messages appear have already been taken care of. Note If you mistakenly press the wrong key, press CLR and start again from the beginning. Input devices External power supply output: Page 82 Wiring and Connections Section Input Devices The following table shows how to connect various input devices.

Section Example Mabual The following ladder program will be used to demonstrate how to write a pro- gram with the Programming Console.

Structure And Operation It will be necessary to turn the power off and then on again to enable a new setting if the parameter is ac- cessed only when the power is turned on. Hexadecimal, Bcd Data Modification 3. Unsigned Decimal Monitor Three-Word Cpm2q Modification This operation is used to change the contents of one or more of the 3 con- secutive words displayed in the Three-Word Monitor operation.

Insert the battery into the compartment, making sure that the cord on the battery is facing the connector on the manuaal side inside the compartment. Functional ground terminal AC power supplies only 5.

  CONVERTIR FICHEROS XPS A PDF

Wiring and Connections Section Input Devices The following table shows how to connect various input devices. Page 20 EC Directives Countermeasure Examples When switching an inductive load, connect a surge protector, diodes, nanual. Failure to do so may result in Unit malfunction.

OMRON CPM2A – 11-2005 Manual

Lift up the lock lever. Page 19 EMC Directives. The program check will begin when the check level is input, and the first error found will be displayed. Programming Console, —,cpm2s, buzzer operation, Programming Console, 99 data link, 6, 86 date. The status of the displayed words can be changed at this point. Note The default setting is By pressing ‘print’ button you will print only current page. It will be necessary to turn the power off and then on again to enable a new setting if the parameter is ac- cessed only when the power is cpma2 on.

Page 59 Unit Components Section Page 8 Section 4 describes how to connect the Programming Console, and how to perform the various program- ming operations. Page of Go. Not doing so may result in mal- function or damage. Specifications Terminal screw size Power interrupt time AC power manal Programming Procedures Example Program. Multiple address monitor 2.