DGABK datasheet, DGABK pdf, DGABK data sheet, datasheet, data sheet, pdf, Intersil, Quad SPST, CMOS Analog Switches. DGABK Datasheet, DGABK PDF, DGABK Data sheet, DGABK manual, DGABK pdf, DGABK, datenblatt, Electronics DGABK. DGABK datasheet, DGABK circuit, DGABK data sheet: MAXIM – Quad SPST CMOS Analog Switches,alldatasheet, datasheet, Datasheet search site.
|Published (Last):||4 May 2013|
|PDF File Size:||4.9 Mb|
|ePub File Size:||11.81 Mb|
|Price:||Free* [*Free Regsitration Required]|
All Rights Reserved All other trademarks mentioned are the property of their respective owners. Exposure to absolute maximum datashret conditions for extended periods may affect device reliability. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied.
Mold flash or protrusions shall not exceed 0.
Data Sheet catalog: ParNumber from digitIndex DG2
This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Pin Configurations continued To provide protection for overvoltages up to 20V above the supplies, a 1N or 1N type diode should be placed in series with the positive and negative supplies as shown in Figure 2.
Device mounted with all leads soldered to PC board. Documents Flashcards Grammar checker. E and eA are measured with the leads constrained to be perpendicular to datum -C.
For more information on TYP values see Note 2. N is the maximum number of terminal positions. Package Information continued The package drawing s in this data sheet may not reflect the most current specifications. Maxim guarantees that these switches will not latch up if the power supplies are disconnected with input signals still connected. When the enable input is high, a channel is selected by the address inputs, and when low, all channels are off. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders.
For more information on TYP values see Note 3. Putere n-am, Tu-mi fii sprijin. Lab 6 in this note. A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown.
The DG has a maximum turn-off time of ns and a maximum turn-on time of ns. Limit diode current to maximum current ratings. For the latest package outline information, go to www. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. For this configuration dimension b3 replaces dimension b2.
B1 maximum dimensions do not include dambar protrusions. Typical values are for design aid only, not guaranteed and not subject to production testing.
The addition of these diodes will reduce the analog signal range to 1V below the positive supply and 1V above the negative supply.
Measure dimension S1 at all four corners. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use.
Dimension M applies to lead plating and finish thickness. D, D1, and E1 dimensions do not include mold flash or protrusions. In the OFF state each channel blocks voltages up to the supply rails. This dimension allows for off-center lid, meniscus, and datasheeh overrun.
Dimensions b1 and c1 apply to lead base metal only.
Information furnished by Intersil is believed to be accurate and reliable. An enable input is provided. Asa cum catasheet, la Tine vin! SR Datasheet – Micropower Direct.
DG Data sheet, PDF –
VO is the steady state output with switch on. In either case, source-to-body diodes can be forward biased and conduct current from the signal source. For information regarding Intersil Corporation and its products, see www. Dimension Q shall be measured from the seating plane to the base plane.
These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. The DGA has a maximum turn-off time of ns and a maximum turn-on time of ns. The algebraic convention whereby the most negative value is a minimum, and the most positive value is a maximum, is used in this data sheet. Feedthrough via gate capacitance may result in spikes at leading and trailing edge of output waveform. No circuit patent licenses are implied. Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product.
Maxim reserves the right to change the circuitry and specifications without notice at any time. Dambar protrusions shall not exceed 0. Copyright Intersil Americas Inc. Parameter guaranteed by design or characterization.