Europastandarden EN gäller som svensk standard. The European Standard EN has the status of a Swedish. Standards. DIN EN Safety of industrial trucks – Pedestrian propelled manual and semi-manual trucks – Part 3: Platform trucks; German version EN. DIN EN Safety of industrial trucks – Pedestrian propelled manual and semi-manual trucks – Part 3: Platform trucks.

Author: Kazrasida Faugal
Country: Uruguay
Language: English (Spanish)
Genre: Career
Published (Last): 14 February 2015
Pages: 403
PDF File Size: 16.94 Mb
ePub File Size: 18.99 Mb
ISBN: 664-2-46371-635-8
Downloads: 29465
Price: Free* [*Free Regsitration Required]
Uploader: Kigaran

Search all products by. The corresponding requirements are designed to limit the risk or reduce these hazards in each situation. The tiller shall automatically and 17757-3 return to the upper rest position when released.

Worldwide Standards We can source any standard from anywhere in the world. The frequency of the load handling cycle should also be taken into account.

The force shall be applied horizontally along the truck’s axis on the tiller handle or bar. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. Your basket is empty. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this document.

BS EN Safety of industrial trucks – MBA智库文档

We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover.

Users are responsible for its correct application. Two tests in both the forward and reverse directions 17573- be carried out and the average result recorded. The test load, 1757–3 applicable, shall be applied according to clause 3. The test shall not result in any visual permanent deformation or damage. General requirements Part 2: The truck is designed to be manually, pushed, pulled and steered by a pedestrian operator by means of a bar or tiller handle to move loads from one place to another one on a smooth, level, hard surface.

  APA STIJL BRONVERMELDING PDF

The same test shall be carried out when pulling. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services.

You may find similar items within these categories by selecting from the choices below:. The rated capacity shall be easily readable by the operator. During measurement the force continues to be applied tangentially, the wheels swivel freely and are turned crosswise at the end of the measurement.

The maximum starting force EDmax or the maximum rolling force ERmax is the average of the maximum values recorded in each direction of travel, forward AV and reverse AR, during two successive tests.

The tiller shall be maintained in vertical position along the sn axis. A list of organizations represented on this committee can be obtained on request to its secretary. The hand grips shall be of a cross section enclosed within the space between two concentric circles of 25 mm inside diameter and 35 mm outside diameter.

NBN EN 1757-3

Two measurements are recorded in each direction of tiller steering. With the truck stationary, measurement consists of recording the maximum force applied tangentially in the middle of the handle throughout the steering lock in one direction from the tiller’s axial position Figure A. If these details are to be used for any other purpose than implementation 1757-33 the prior written permission of BSI must be obtained. A series of longitudinal and lateral stability tests shall be carried out depending on the truck type with the positions of the truck on the platform as below and Table B.

Summary of pages This document comprises a front cover, an inside front e, the EN title page, pages 2 to 23 and a back cover.

Various BSI electronic information services are also available which enn details on all its products and services. This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3.

  D20 MODERN URBAN ARCANA PDF

The upper part of the tiller handle shall conform to the dimensions shown in Figure 1 and Figure 2. Platform trucks Part 4: The centre of gravity of the load on each level shall be on the centre line of the truck and mm above the geometrical centre of the platform or the shelf 3.

NOTE The forces to operate the truck are varying with the value of the load, the ground conditions and the truck conditions.

For undated references the latest edition of the publication referred to applies including amendments.

BS EN Safety of industrial trucks — Self-propelled trucks up to and including 10 kg capacity and industrial tractors with a drawbar pull up. Except as permitted under the Copyright, Designs and Patents Act no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means — electronic, photocopying, recording or otherwise — without prior written permission from BSI.

Two measurements are recorded in each direction of bar steering. The BSI copyright date displayed in this document indicates when the document was last issued. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards.

It may occasionally be necessary to negotiate small slopes for the purposes of moving the truck between buildings etc. Click to learn more. General requirement for battery powered trucks Part 2: The verification of safety requirements shall be carried out by design verification on truck type plus manufacturing arrangements not described here plus functional routine verification on each truck to verify its fitness for purpose.

Information regarding online access to British Standards via British Standards Online can be found at http: