ISO MECHANICAL VIBRATION – EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON ROTATING SHAFTS – PART 3: COUPLED . Mechanical vibration – Evaluation of machine vibration by measurements on rotating shafts – Part 3: Coupled industrial machines (ISO. Full text of “IS/ISO Mechanical vibration – evaluation of machine vibration by measurements on rotating shafts, Part 3: Coupled Industrial Machines”.

Author: Tozil Vijind
Country: Burundi
Language: English (Spanish)
Genre: Music
Published (Last): 22 August 2006
Pages: 353
PDF File Size: 10.53 Mb
ePub File Size: 9.51 Mb
ISBN: 506-6-29694-581-8
Downloads: 64465
Price: Free* [*Free Regsitration Required]
Uploader: Kajigrel

These values are not intended to 7919–3 as acceptance specifications, which shall be subject to agreement between the machine manufacturer and the customer. Various BSI electronic information services are also available which give details on all its products and services. To provide a warning that a defined value of vibration has been reached or a significant change has occurred, at which remedial action may be necessary.

MED 28 1 Quoting “The values given in Tables A. The values used will, therefore, generally be the same for all machines of similar design and would not 79919-3 be related to the steady-state baseline value used for setting ALARMS.

Copyright BIS has the copyright of all its publications.

ISO 7919-3 | AMP Maintenance Forums

The vibration of newly commissioned machines normally falls within this zone. Machine behavior can be very much dependent on construction details, hence why I suggest you research the OEM guidelines. The criteria are presented for the specified steady-state operating conditions 7199-3 the rated speed and load ranges.

After a period of time, the steady-state baseline value will be established and the ALARM setting should be adjusted accordingly.

In such cases the evaluation zone limits should be adjusted accordingly. In such cases, it is normally necessary to explain the reasons for this and, in particular, to confirm that the machine will not be endangered by operating with higher vibration values. Generally, the machine may be operated for a limited period in this condition until a suitable opportunity arises for remedial action.

This does not preclude the free use, in course of imple- menting the standard, of necessary details, such as symbols and sizes, type or grade designations. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

If the steady-state baseline changes for example, after a machine overhaulthe ALARM setting should be revised accordingly. In particular, it should be recognized 7919-33 the allowable vibration can be related to the journal diameter since, generally, running clearances will be greater for larger diameter bearings. Have you added an attachment with your post? A decision on what action can be taken, if any, should then be made after consideration of the maximum value of vibration and whether the izo has stabilized at a new condition.

  ESSO UNIVIS J13 PDF

Adobe is a trademark of Adobe Systems Incorporated. These values are not intended to serve as acceptance specifications, which shall be subject to agreement between the machine manufacturer and the customer.

ISOMechanical vibration of non-reciprocating machines — Measurements on rotating shafts and evaluation criteria — Part 1: Specifications like the ISO spec you site are going to be generic in nature since the construction of a machine may have considerable affect on its behavior.

Different manufacturers may also have their own guidelines for limits when passing through critical speeds.

As far as specific standards, as I said earlier the OEM 79193 has some guidelines, often specific to a given model of machine. Such things are often in the Tech manual. Consequently, it can be difficult to identify the effects of the crack propagation by looking at the change in the broad-band vibration only. If the TRIP limit ido exceeded, immediate action should be taken to reduce the vibration or the machine should be shut down.

ISO | AMP Maintenance Forums

Machines with vibration within this zone are normally considered unsatisfactory for long-term continuous operation. The recommended values illustrated in Figure A. Mechanical vibration – evaluation of machine vibration by measurements on rotating shafts, Part 3: In this adopted standard, reference appear to the following International Standard for which Indian Standard also exists.

In general, if an ALARM situation occurs, operation can continue for a period whilst investigations are carried out to identify the reason for the change in vibration and define any remedial action. No part of these publications may be reproduced in any form without the prior permission in writing of BIS. These guidelines are presented in terms of both steady running vibration and any amplitude changes which can occur in these steady values. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.

  HETEROSIDOS FENOLICOS PDF

Sometimes getting the OEM recommendation may involve making a phone call isl an email. The criteria are presented for the specified steady-state operating conditions at the rated speed and load ranges. This equipment can be more sophisticated than that used for normal supervisory monitoring and its use and application requires specialist knowledge. General guidelines [2] ISOMechanical vibration — Evaluation of machine vibration by measurements on non-rotating parts — Part 3: Every care has been taken to ensure that the file is suitable isk use by ISO member bodies.

However, they provide guidelines for ensuring that gross deficiencies or unrealistic requirements are avoided. The recommended values Illustrated In Figure A.

BS ISO 机械振动.通过对旋转轴的测量评估机械振动.耦合工业机械 – MBA智库文档

In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address 799-3 below.

In particular, the conditions for in-situ operation, performing acceptance tests and the influence of bearing clearance given in ISO shall be taken into account when evaluating the shaft vibration of ixo This part of ISO is neither applicable to land-based steam turbine-generator sets for power stations with outputs greater than 50 MW see ISOnor machine 7919-33 in hydraulic power isso and pumping plants with outputs of 1 MW or greater see ISO Therefore, unless stated otherwise, this part of ISO always refers to relative vibration displacement.

ISO consists of the following parts, under the general title Mechanical vibration — Evaluation of machine vibration by measurements on rotating shafts: Caution should be isk when using the criteria presented in Annex A to ensure that no contact occurs between the rotating shaft and stationary parts. The values used will, therefore, generally be the same for all machines of similar design and would not normally be related to the steady-state baseline value used for setting ALARMS.

In industrial machines, shaft vibration relative to the bearing is normally measured. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover.